Tikalon Header Blog Logo

Pliable Resin

December 6, 2011

When I was still performing laboratory experiments, I would try to do these as cheaply as possible. There's no sense in spending too much money on a proof-of-concept device when that device might show that your concept is not that good. One of my favorite materials in this work was one of the many variants of "five-minute" epoxy. It's nice to have an adhesive that does its job after just a few moments of holding or clamping.

Of course, there's the danger of doing things so fast and dirty that your device doesn't work simply because it's too shoddy. In the 1960s, when I was still in high school, a veteran electrical engineer told me about the circuit breadboards his colleagues would build that couldn't possibly work because of poor solder workmanship. Their circuit designs didn't fail, but their poor craftsmanship led them to believe that they did.

Five minute epoxy

A Phrugal Physicist's Phriend.

Five minute epoxy served the same purposes in my laboratory as sealing wax did in Rutherford's time.

Photograph by Dzhang2680, (via Wikimedia Commons))


Epoxy works fine if you don't need to slightly realign your joint. Once it's set, it locks your components in place, which can be an advantage in some cases, but not in others. Ernest Rutherford's people used sealing wax in the same way that I used fast-setting epoxy, but application of a little heat allowed realignment of the components in their experiments, but not mine. It would be nice to have a heat-softenable resin that would give you the advantages of sealing wax, but the mechanical properties of a hard material.

Scientists at the Department of Matière Molle et Chimie of the Ecole Supérieure de Physique et Chimie Industrielles (Paris, France) have produced materials with such properties, and they reported on their research in a recent issue of Science.[1-5] They endeavored to produce the beneficial properties of permanently cross-linked materials, such as solvent resistance and mechanical resilience and strength in a pliable material.

Their approach was to design epoxy networks with molecules that can rearrange their topology by exchange reactions. Their materials show the desireable behaviour of not abruptly changing viscosity at a glass transition temperature. Instead, the viscosity of their materials shows an Arrhenius law behavior much like that of vitreous silica. As a consequence, the materials can be worked just like a glass under heat.[2]

Topological rearrangement by transesterification

One example of a topological rearrangement process - transesterification in hydroxy-ester networks. See fig. 1B of Ref. 2. (Illustration by author).


This functionality derives from the material's ability to rearrange its molecules without changing the number of cross-links between molecular units. These materials can be designed to be either elastomeric, or hard and rigid, depending on composition. With application of heat, these materials can be shaped, as shown in the photograph, below. When used as the matrix phase in composites, these materials can compete with metals in some applications.[1]

CNRS pliable resin

A strip of pliable resin being worked by hand over a hot air gun.

Note the thermocouple arranged to allow fine control of the working temperature.

(CNRS image))


There's an online video showing the piable properties of these materials.[5] This work was supported by CNRS.[1]

References:

  1. Priscilla Dacher, "New revolutionary material can be worked like glass," CNRS Press Release, November 16, 2011.
  2. Damien Montarnal, Mathieu Capelot, François Tournilhac and Ludwik Leibler, "Silica-Like Malleable Materials from Permanent Organic Networks," Science, vol. 334, no. 6058 (November 18, 2011), p. 965-968.
  3. Supporting Online Material for Ref. 2.
  4. This Week in Science: Editor summaries of this week's papers - Not So Thermoset, Science, vol. 334, no. 6058 (November 18, 2011), p. 875.
  5. Video of material pliability for Ref. 2.                              

Permanent Link to this article

Linked Keywords: Laboratory; experiment; proof-of-concept; epoxy; adhesive; high school; electrical engineer; circuit breadboard; solder; circuit design; sealing wax; Ernest Rutherford; Wikimedia Commons; heat; resin; Department of Matière Molle et Chimie; Ecole Supérieure de Physique et Chimie Industrielles (Paris, France); Science; cross-linked; solvent; mechanical resilience; strength; topology; exchange reaction; viscosity; glass transition temperature; Arrhenius law; fused quartz; vitreous silica; hydroxy; ester; molecule; elastomeric; matrix phase; composite; metal; CNRS; French National Centre for Scientific Research.